DIN 50324 PDF

DIN 50324 PDF

Standard [WITHDRAWN] DIN Tribology; testing of friction and wear model test for sliding friction of solids (ball-on-disc system). Buy DIN TRIBOLOGY; TESTING OF FRICTION AND WEAR MODEL TEST FOR SLIDING FRICTION OF SOLIDS (BALL ON DISC SYSTEM) from. Find the most up-to-date version of DIN at Engineering

Author: Branris Aralrajas
Country: Gabon
Language: English (Spanish)
Genre: Travel
Published (Last): 26 August 2013
Pages: 31
PDF File Size: 13.42 Mb
ePub File Size: 8.84 Mb
ISBN: 148-2-89883-363-8
Downloads: 50566
Price: Free* [*Free Regsitration Required]
Uploader: Monos

Real time down force controlpiezo sensors to measure inline friction makes this module very reliable and repeatable. The test involves rotating one ball on three stationary balls at controlled environmental conditions.

In this latter case, the results cannot be compared to the ILS data Table 2.

High-load and high-temperature tribometer – Fraunhofer IST

Materials are tested in pairs under nominally non-abrasive conditions. Loads from mN to 10,N. Work Item s – proposed revisions of this standard. 53024 and recirculation addons are also available.

High-load and high-temperature tribometer

Piston Ring Liner This test helps evaluate friction and wear parameters of piston ring liner material in presence of engine oils. In all modules listed above user can change the load and velocity to automatically plot Stribeck Curves with ease.

Fast Exchange makes all these modules easily swapable on the MFT platform. Referenced Documents ddin separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The value of any wear test method lies in predicting the relative ranking of material combinations. The test setup allows to mount real pieces of actual piston ring and liners.

  KAMIL AL ZIYARAT PDF

The principal areas of experimental attention in using this type of apparatus to measure wear are described. Contact us for a live Demo or additional information.

Test involves slowly rotating a ring on top of material of choice.

Tapping Torque, Twist Compression, Drilling Tapping torque module allows to characterize friction, wear, torque etc. Linear Oscillating The standard Test to determine extreme pressure, friction wear properties of lubricant greases, solid bonded films, gear and hydraulic fluids, lubricating oils. All tests are done in oscillation mode under controlled environmental conditions.

However, it must be clearly stated in any report that, while the directions and protocol in Test Method G99 were followed if truethe choices of test parameters were different from Test Method G99 values, and the test results were therefore also different from the Test Method G99 results.

Stribeck curve ein a plot between coefficient of friction and bearing number. This dim helps evaluate friction and wear parameters of piston ring liner material in presence of engine oils. Stribeck Curve Stribeck curve is a plot between coefficient dun friction and bearing number. The ball is caused to rub against 5024 disk 1mm stroke at a frequency of 50 Hz for 75 min.

  DAN ZARRELLA THE SOCIAL MEDIA MARKETING BOOK PDF

The coefficient of friction may also be determined. The standard Test to determine extreme pressure, friction wear properties of lubricant greases, solid bonded films, gear and hydraulic fluids, lubricating oils.

The tests can be done in controlled environmental conditions including humidity, temperature and more.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. No other units of measurement are included in this standard. Link to Active This link will always route cin the current Active version of the standard.

Such a use of this standard is encouraged as a means to improve wear testing methodology.

Thank you for your interest and filling out the form! Twist Compression is designed to measure friction and adhesion in metal forming.

503244 Version s – view previous versions of standard. Since the pin-on-disk test method does not attempt to duplicate all the conditions that may be experienced in service for example; lubrication, load, pressure, contact geometry, removal of wear debris, and presence of corrosive environmentthere is no insurance that the test will predict the wear rate of a given material under conditions differing from those in the test.