DIN 50324 PDF

DIN 50324 PDF

Standard [WITHDRAWN] DIN Tribology; testing of friction and wear model test for sliding friction of solids (ball-on-disc system). Buy DIN TRIBOLOGY; TESTING OF FRICTION AND WEAR MODEL TEST FOR SLIDING FRICTION OF SOLIDS (BALL ON DISC SYSTEM) from. Find the most up-to-date version of DIN at Engineering

Author: Samukasa Tuzahn
Country: Slovenia
Language: English (Spanish)
Genre: Environment
Published (Last): 26 May 2009
Pages: 389
PDF File Size: 13.2 Mb
ePub File Size: 10.78 Mb
ISBN: 674-2-80066-754-9
Downloads: 61916
Price: Free* [*Free Regsitration Required]
Uploader: Gardami

Twist Compression is designed to measure friction and adhesion in metal forming. The standard Test to determine extreme pressure, friction wear properties of lubricant greases, solid bonded films, gear and hydraulic fluids, lubricating oils.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Real time down force controlpiezo sensors to measure inline friction makes this module very reliable and repeatable.

This test helps evaluate friction and wear parameters of piston ring liner material in presence of engine oils. The value of any wear test method lies in predicting the relative ranking of material combinations. Piston Ring Liner This test helps evaluate friction and wear parameters of piston ring liner material in presence of engine oils.

However, it must be clearly stated in any report that, while the directions and protocol in Test Method G99 were followed if truethe choices of test parameters were different from Test Di G99 values, and the test results were therefore also different from the Test Method G99 results. The coefficient of friction may also be determined.

  EPIFISIOLISTESIS CLASIFICACION PDF

Thank you for your interest and filling out the form! The ball is caused to rub against the disk 1mm stroke at a frequency of 50 Hz for 75 min. Since the pin-on-disk test method does not attempt to duplicate all the conditions that may be experienced in service for example; lubrication, load, pressure, contact geometry, removal of wear debris, and presence of corrosive environmentthere is no insurance that the test will predict the wear rate of a given material under conditions differing from those in the test.

Test involves slowly rotating a ring on top of material of choice. Fin principal areas of experimental attention in using this type of apparatus to measure wear are described.

High-load and high-temperature tribometer

Loads from mN to 10,N. All tests are done in oscillation mode under controlled environmental conditions. Historical Version s – view previous 5032 of standard. Work Item s – proposed revisions of this standard. Tapping Torque, Twist Compression, Drilling Tapping torque module allows to characterize friction, wear, torque etc.

ASTM G99 – 17 Standard Test Method for Wear Testing with a Pin-on-Disk Apparatus

Contact us for a live Demo or additional information. The tests can be done in controlled environmental conditions including humidity, dih and more. Linear Oscillating The standard Test to determine extreme pressure, friction wear properties of lubricant greases, solid bonded films, gear and hydraulic fluids, lubricating oils.

  ECCEMA ATOPICO PDF

Temperature and recirculation addons are also available. In this latter case, the results cannot be compared to the ILS data Table 2. It is the responsibility dib the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. In all modules listed above user can change the load and velocity to automatically plot Stribeck Curves with ease.

Such a use of this standard is encouraged as a means to improve wear testing methodology. Stribeck Curve Stribeck curve is a plot between coefficient of friction and bearing number. Materials are tested in pairs under nominally non-abrasive conditions.

Link to Active This link will always route to the current Active version of the standard. The test setup allows to mount real pieces of actual piston ring and liners.

Fast Exchange makes all these modules easily swapable on the MFT platform. No other units of measurement are included in this standard.

Stribeck curve is a plot between coefficient of friction and bearing number. The test involves rotating one ball on three stationary balls at controlled environmental conditions.